Select System Status > VPN Statistics. Verify that the VPN tunnel is active. To test the integration, from the FortiGate Web UI: Select Monitor > IPsec Monitor. Verify that the VPN tunnel is active. Finally, verify that the servers at Host1 and Host2 can successfully ping each other.
This blog post is a list of common troubleshooting commands I am using on the FortiGate CLI.It is not complete nor very detailled, but provides the basic commands for troubleshooting network related issues that are not resolvable via the GUI. Remove any Phase 1 or Phase 2 configurations that are not in use. If a duplicate instance of the VPN tunnel appears on the IPsec Monitor, reboot your FortiGate unit to try and clear the entry. If you are still unable to connect to the VPN tunnel, run the following diagnostic command in the CLI: Two FortiGate units; Third-party VPN software and a FortiGate unit For more information on third-party VPN software, refer to the Fortinet Knowledge Base for more information. Tunnel templates. Several tunnel templates are available in the IPsec VPN Wizard that cover a variety of different types of IPsec VPN. add vpn tunnel 1 type numbered local 169.254.44.234 remote 169.254.44.233 peer AWS_VPC_Tunnel_1 set interface vpnt1 state on set interface vpnt1 mtu 1436 Repeat these commands to create the second tunnel, using the information provided under the IPSec Tunnel #2 section of the configuration file. Here comes the step-by-step guide for building a site-to-site VPN between a FortiGate and a ScreenOS firewall.Not much to say. I am publishing several screenshots and CLI listings of both firewalls, along with an overview of my laboratory.
I have had a IPSEC connection setup between two firewalls. Now I want to remove the tunnel in my firewall, a "Fortigate 60". There are two phases, "Phase 1" and "Phase 2" for each IPSEC connection. I can delete the "Phase 2" entry by clicking the trashcan icon (in the web interface), but there is not such icon for "Phase 1".
Jan 23, 2013 · The NPS/RADIUS server i need to reach is on the other side of an IPSec tunnel, which is working fine, and i am able to log in with accounts from the AD. However i can't really seem to figure out how the authentication should be set up. The FortiGate is already set up as an RADIUS client on the Windows Server. Jan 23, 2013 · One thing that is not clear is whether you are using dynamic (dial-up) tunnels or normal site to site tunnels. If you are using dynamic tunnels, you can use aggressive mode in conjunction with a peer id to direct clients to the correct vpn tunnel based on that rather than their client ip. Aug 19, 2012 · I have a vpn tunnel setup between a Fortigate 100 and Fortigate 60C at a remote site. I am using our standard internet connection instead of a separate circuit. I have two networks setup, one here, and a different one there, and traffic is automatically routed to the distant network based upon which network ID it belongs to. Jul 18, 2015 · This video shows Fortigate firewall SSL VPN features. FortiGate Cookbook - SSL VPN Web and Tunnel Mode (5.4) - Duration: 7:21. Fortinet 87,973 views. 7:21. Language: English
A standard fortigate vpn tunnel interface does not have an ip address. As such, there is no way to peer between the firewalls. The process of creating a redundant vpn connection is the same as a standard fortigate to fortigate tunnel. You first have to configure two independant vpn tunnels over the two internet connections.
I have had a IPSEC connection setup between two firewalls. Now I want to remove the tunnel in my firewall, a "Fortigate 60". There are two phases, "Phase 1" and "Phase 2" for each IPSEC connection. I can delete the "Phase 2" entry by clicking the trashcan icon (in the web interface), but there is not such icon for "Phase 1". Nov 25, 2016 · Debug and troubleshoot an IPSEC VPN tunnel on a FortiGate The logging on a FortiGate firewall is very scarse, making it difficult to troubleshoot issues. This can especially be a problem when setting up a site-to-site IPSEC VPN tunnel.